Preparation Before Operating System
The device needs to be maintained tidy
Wood as well as materials to be kept in area temperature
When the humidity of the processed product is too expensive, it will certainly affect the adhesion
When Edge banding, to offer the ideal pressure to the workpiece, not nearly enough pressure will certainly influence the quality of
Shop warm thaw adhesive in an awesome, dry
When Hot thaw glue is cool, need to not be compelled to open the melting pot cover or the glue adjusting knob, to avoid damage to the machine
Prior to side banding, make sure that the warm melt adhesive in the fusion is already common
The diameter of the internal arc shall not be less than 40mm
Please make use of the reduced temperature level hot thaw adhesive 120-180 ℃ suggested by our (Maximum temperature level shall not exceed 200 ℃).
Temperature And Speed Control.
Optima 2.0 does not have the function of edge tape heating. Opitma2.1 has the feature of side tape heating, which appropriates for home heating and also conditioning of extremely low temperature level or thick securing strip, making the securing result much more Two versions can regulate the edge banding machine, the temperature level of the colloid particles of the do adjustment in 120-180 ℃.
After the power switch on, the temperature level controller presents the present temperature( in red), adjust the temperature (in eco-friendly) with the thermostat panel, the interior relay is activated and the light gets on. Thermostat with power off memory function, temperature level no requirement to reset after detaching the power supply.
Temperature level control indication: when the heating is started, the light gets on.
Operation indication: When the temperature reaches the set temperature, the motor button light will certainly turn on, and also the motor switch can be turned on to accelerate the gel melting.
After the motor button lamp gets on, turn on the switch, change the readjusting handle to the appropriate speed, then start securing.
Curve/straight switch need to be closed by the electric motor switch to work.
Operation Mode.
- Strake height adjustment.
Loosen up the handle of the front height limiting gadget.( photo 1).
Place the edge in the high limitation for determining stress to restrict the high wing, subjected to the edge, locking the knob.( picture 2 & picture 3).
With reference to the height of the work surface, position the workpiece under the platen roller and also china manual edge banding machine press down the platen wheel and also the work surface to the major surface of the maker, leaving a correct spacing and locking the flexible take care of. Readjust the adjustable deal with to release (Figure 4), after the change is completed, after that the deal with is secured.
- Readjust the amount of adhesive.
When the temperature of the edge banding machine reaches the working temperature level, reduced a piece of side (regarding 20CM/8″) right into the test, change the adhesive volume handle to the suitable quantity, and allow the melt on the edge band be evenly layered.
saftey guidelines Note that when the hot melt is cooled down, a few of the framework is stuck and also the adjustment handle can not be transformed.
- Grouping tape thickness modification: when the edge is also thin or also soft, adjust the thickness changing knob as well as fixing screw, to let side banding perfect.
- Operation.
When the banding tape is grouped to the workpiece, correct stress needs to be put on increase the banding result.
After verifying that there is no residue in the edge banding machine, open the starter button of the edge banding machine. When the temperature level of the warm thaw glue in the hot thaw adhesive cyndrical tube reaches the collection temperature, the indication light (1) of the motor switch button lights up as well as can be pressed (1) The switch permits the thaw cycle to speed up According to different warm thaw adhesives, it is necessary to wait for the glue to completely melt. The processing board is laid level on the panel, and the timber board is pushed versus the limit turn on the stopper. The processing board is close to the gluing shaft and the beginning factor of the gluing shaft is about 5 CENTIMETERS. The board is weighed down by the edge of the board, the edge button presses the pulley. The cyndrical tube is pushed versus the feeding wheel to drive the securing strip to the shaft. The refined product is pressurized with moderate stress and pushed versus the driving wheel for side banding when the sealing strip reaches the driving wheel with the gluing shaft.
Production Machines 